Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when ordering parts.
Carefully remove the fixture from the carton and check that all parts are
included, as shown in Figure 1 & 2. Be careful not to misplace any of the
screws or parts which are needed to install this fixture.
FIGURE 2
*NOT INCLUDED
BEFORE YOU BEGIN
Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
HC-1505
1
12608
• Be sure the electricity to the system you are working on is turned off;
either the fuse removed or the circuit breaker set at off.
• Use of other manufacturers components will void warranty, listing and
create a potential safety hazard.
• If you are unclear as to how to proceed, contact a qualified electrician.
• You don’t need special tools to install this fixture.
• Be sure to follow the steps in the order given.
• Under no circumstances should a fixture be hung on house electrical
wires, nor should a swag type fixture be installed on a ceiling which
contains a radiant type heating system.
• Read instructions carefully.
• Save these instructions.
IMPORTANT SAFETY INSTRUCTIONS
Unscr
ew lockwasher/nut (L) from rod (K). Remove fixture loop (V) and top
plate (J), attached to center pipe (M).
STEP 1:
Feed fixture wires from center pipe (M) through canopy (Z). Secure in place
with lock washer (T) and nut (S).
STEP 2:
Attach short ends of the three rods (K) to the canopy (Z) with lock washer and
nuts (L).
STEP 3:
IF SUPPLY WIRES ARE LOCATED WITHIN 3” OF BALLAST, USE WIRE
RATED FOR AT LEAST 90˚C.
WARNING: RISK OF FIRE. MOST DWELLINGS BUILT BEFORE 1985
HAVE SUPPLY WIRE RATED 60˚C. CONSULT A QUALIFIED ELECTRICIAN
BEFORE INSTALLING. FOR SUPPLY CONNECTIONS, USE WIRE
SUITABLE FOR AT LEAST 90˚C.
Attach fixture loop (V) to the threaded nipple on top of the fixture (if applicable).
FOR CHAIN HUNG (Figure 1)
FIGURE 1
*NOT INCLUDED
Attach fixture loop (V) to the threaded nipple on top of the fixture (if applicable).
FOR FLUSH MOUNT (IF APPLICABLE) (Figure 2)
FOR CHAIN
HUNG
FOR FLUSH MOUNT
*OUTLET BOX
*WIRE
CONNECTOR
CANOPY (G)
*OUTLET BOX
SCREWS
MOUNTING
BAR (A)
CHAIN (N)
FIXTURE LOOP (V)
TOP PLATE (J)
CENTER
PIPE (M)
ROD (K)
LOCKWASHER/
NUT (L)
RUBBER
WASHER
(N)
TRIM
RING (O)
CHECK
RING (P)
BALL
NUT (Q)
GLASS (R)
NIPPLE (C)
*GROUND WIRE
GROUND WIRE (E)
SCREW COLLAR (H)
SCREW COLLAR
RING (F)
GREEN
GROUNDING
SCREW (D)
NUT (B)
*OUTLET BOX
*WIRE
CONNECTOR
CANOPY (Z)
*OUTLET BOX
SCREWS
MOUNTING
BAR (A)
ROD (K)
*GROUND WIRE
NUT (S)
CAP NUTS (U)
LOCK WASHER (T)
MOUNTING
SCREWS (I)
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not
use abrasive materials such as scouring pads or powders, steel wool or
abrasive paper.
CLEANING
ORDERING PARTS
NIPPLE (C)
(3 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels