Sea gull lighting 7355-15 Guide d'installation

Naviguer en ligne ou télécharger Guide d'installation pour Non Sea gull lighting 7355-15. Sea Gull Lighting 7355-15 Installation Guide Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 2
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
ASSEMBLY
GENERAL
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU
ARE WORKING ON IS SHUT OFF. EITHER THE FUSE REMOVED
OR THE CIRCUIT BREAKER OFF.
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Under no circumstances should a fixture be
hung on house electrical wires, nor should a swag type fixture be
installed on a ceiling which contains a radiant type heating system.
Read instructions carefully. If you are unclear as to how to proceed,
consult a qualified electrician.
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1 & 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
NOTE: Socket may be factory installed.
GREEN
GROUNDING SCREW (Z)
*OUTLET BOX
SCREWS
MOUNTING
BAR (A)
*WIRE
CONNECTORS
MOUNTING
SCREWS (I)
*GROUND WIRE
*OUTLET BOX
GROUNDING AND MOUNTING BAR LOCK UP
FIGURE 2
*NOT INCLUDED
FIGURE 1
*NOT INCLUDED
*OUTLET
BOX
*WIRE
CONNECTORS
CANOPY (B)
DIFFUSER (I)
WARNING: FOR FIXTURES PROVIDED WITH 75˚ C
OR 90˚ C SUPPLY WIRE WARNING ONLY (THESE
WARNINGS ARE PROVIDED ON THE U.L. LABEL
AND ON THE FIXTURE CARTON).
WARNING: RISK OF FIRE. MOST DWELLINGS
BUILT BEFORE 1985 HAVE SUPPLY WIRE RATED
60˚ C. CONSULT A QUALIFIED ELECTRICIAN
BEFORE INSTALLING.
KEY HOLE (C)
STEP 1:
To clear a path through canopy (B) fiberglass, push screwdriver
through canopy center hole (D).
STEP 2:
Position center holes (D) over one another so that the fiberglass is
visible through all holes.
STEP 3:
Pass the fixture wires through center hole (D) in canopy (B). Align
socket clip (E) and canopy (B) center hole (D) and push together
until socket (F) locks. Secure in place by inserting a screw-driver
blade through each side of clip and pry outward (if applicable).
STEP 4:
Push screwdriver blade through keyholes (C) to clear a path for
mounting screws (I).
FIXTURE
MOUNTING
SCREWS (I)
CENTER HOLE (D)
SOCKET CLIP (E)
SOCKET (F)
NIPPLE (G)
FIBER WASHER (H)
KNOB (J)
MOUNTING BAR (A)
*OUTLET
BOX SCREWS
NOTE: FOR FIXTURE EMPLOYING A GROUNDED
CONVENIENCE OUTLET
CAUTION: “THIS FIXTURE EMPLOYS A GROUNDED TYPE
RECEPTACLE AND IS NOT INTENDED FOR CONNECTION
TO A TWO WIRE UNGROUNDED SOURCE OF SUPPLY.”
Installation And Safety
Instruction
HC-166
092800
Fill In Item Number On Carton And
File This Sheet For Fixture Reference. ITEM#_______________
®
Vue de la page 0
1 2

Résumé du contenu

Page 1 - Instruction

INSTALLATION AND SAFETY INSTRUCTIONSFOR YOUR SAFETYASSEMBLYGENERALWARNING: BE SURE THE ELECTRICITY TO THE WIRES YOUARE WORKING ON IS SHUT OFF. EITHER

Page 2

Install lamps.Thread nipple (G) into socket (F) (NOTE: Nipple may be factory installed).GROUNDING INSTRUCTIONS: Your fixture can be grounded in avari

Commentaires sur ces manuels

Pas de commentaire